Compatible with all Screw Drive Openers Including:

•  EXCELERATOR GS980/9800/880/8800 - GS820/8200/7200/850/800 PRO82/98/88/90 - PRO83/93 - PRO88S/98S CM7500/8500/7500S/8500S - G-CL SERIES - IS SERIES CSD 0706 - CSD 0800 CM7600-IC - CM8600-IC - PRO95 404 - 450 - 409 - 459 - 411 - 419A - 420 - 414 - 429 - 419 - 800 8200 - 8800
• Compatible with CM8600
• SD SERIES - 9500/9000/8000/2500/5000 GXL/GX/G
• SERIES - 9500/9000/2500/5000/10000
• OverHead Door - Signature Models

1 3/4 oz. tube

• Don't forget to lube your garage door and opener for quieter operation
• Multi-purpose, extreme pressure, water repellent grease
• Prevents wear and corrosion, super lubrication
• Ideal for pressure fittings, wheel bearings, garage door opener hardware
• For chains, cables, rusty nuts and bolts... perfect for general lubrication  
• Manufacturer part number 11386
• LUBRIPLATE LBR-ST is recommended for a large variety of applications:
• Trailer landing gear cases
• Speedometers, odometers and techometersParking meters -- Change boxes
• Instruments -- Gaming machines
• Garage and door opening mechanisms
• Cables of various types
• Steering columns and gear cases
• TV antenna gear boxes
• O-Ring and seal lubrication
• Railway switch and signal equipment

Genie Screw Drive Garage Door Opener Replacement Coupler 30257T

 Attaches rail assembly to motor head. Mounts to rear of opener and fits in motor head

 For Clutchless Screw Drive Openers

 Genuine Genie Replacement Part

 Typical symptoms of a stripped Screw Coupler is a grinding noise coming from the rear of the motor head. The motor turns but the screw does not. Remove Coupler and check if it is stripped or has no more threading

 On Genie's "clutchless" openers, there is a small plastic coupler that connects the screw assembly to the main power head. To inspect and replace that part, remove the two screws holding the rail to the main power head. Slide the rail away from the main power head. The coupler may still be attached to the motor shaft. Remove the coupler with a pair of needle nose pliers and inspect both sides of the coupler. Note: If the screw assembly on your Genie garage door opener protrudes out the back end of the main power head, you do not have a "clutchless" opener, and there is no coupler on that opener.

• Genie Replacement Carriage for Chain Drive Garage Door Openers
• Genie Chain Drive Garage Door Opener Replacement Carriage
• Direct replacement for all Genie Chain Drive Openers with Steel T-Rail Assemblies
• Replaces Genie Garage Door Opener part 20438R
• Original Genie Manufactured Replacement Part

Genie Belt Drive Garage Door Opener Parts Description:

For Genie Garage Door Opener Belt Drive model openers. For Genie Garage Door Opener Belt Drive models: GPS1200-IC, GPS700-IC, PRO706-BC, PRO0800-BC, PRO1000-BC, PRO1200-BC Also Replacement For Chain Channel PMX500-7'6''CC,8'CC,10'CC

GENIE Carriage Chain Glide 20466R

• Genie Carriage for Chain Glide Opener models PCG450, PCG650 and GCG350L.
• Requires an inner slide, part #34516R.
• Note: GENIE Carriage and inner slide for Chain Glides PCG400, PCG600, and GCG350 are no longer made.
• When replacing the carriage or inner slide for these models, you need to convert to the 20466R carriage and its accompanying 34516R inner slide.

Genie Replacement Carriage With Innerslide 35263R

for Models PCG400,PCG600,and PCG350

This kit also replaces inner slide and carriage for part #33048A